Hana Modz Pack v2

Overview

The HANA MODZ Pack V2 is a DNA20 controlled battery pack with 510 connector. Variable Watt battery pack that lets you control wattage not voltage, for better consistency and repeatability. Built using quality components. Body is made of 6061 Billet Aluminum. Power regulated digital switch-mode DC-DC converter. It features a small OLED display, buttons and synchronous rectification for maximum battery life and minimal heat generation. The separate UP and DOWN allow the user to increase or decrease the power level in   .1 Watt increments. Built in DNA Charger, which is MICRO USB powered and provides a 500 milliamp charge current. 


Battery must be installed in the proper position. + Positive side of battery towards the top of the device.


Damage can occur if the battery is installed improperly. 


BATTERY NOT INCLUDED:
We recommend using an AW IMR High Drain 18650 Lithium-Ion.
Operating Discharge Temperature : -10 - 60 Degree Celsius
WARRANTY WILL BE VOID IF YOU EXCEED THE OPERATING DISCHARGE TEMPERATURE.
USE AT YOUR OWN RISK.  

USERS GUIDE:
Normal Operation Watt setting: The power level currently set on the DNA 20. Battery indicator: The current state of charge of the battery.


 


Volts display: The current or most recent output voltage being supplied to the atomizer.


 


Ohms display: The resistance of the atomizer attached to the device. This is measured only when the unit is supplying power to the atomizer. At other times, it shows the most recent measurement.


 


Other modes


 


Locked mode: Pressing the fire button five times with less than .7 seconds between presses will cause the device to enter Locked mode. In Locked mode, the device will not fire and the output power will not adjust accidentally. While in Locked mode, the screen will be off, except that pressing a button will show “Locked, Click 5X”. To exit Locked mode, press the fire button 5 times.


 


Stealth mode: While locked, pressing the fire and down buttons simultaneously for five seconds will switch to stealth mode. In this mode the display is off. It will still show error messages and the “Locked, Click 5X” advisory. To switch back to normal display mode, from locked mode hold down the fire and down buttons simultaneously for 5 seconds. This setting is stored to internal flash memory, and remains if power is removed.


 


Right Mode and Left Mode: While locked, holding the fire and up buttons simultaneously for 5 seconds flips the display. This setting is stored to internal flash memory, and remains if power is removed. 


 


Error Messages


The DNA 20 will indicate a variety of error states.


 


Check Atomizer: The DNA does not detect an atomizer, or the atomizer has shorted out.


 


Shorted: The atomizer or wiring are short circuited.


 


Check Battery: The battery is below 3.1 volts. It probably needs to be charged.


 


Weak Battery: The battery sags excessively when firing. This typically means the user is not using a high rate battery, or the battery is old and degraded. It can also mean the battery is not making good contact.


 


Too Hot: The DNA 20D has onboard temperature sensing. It will shut down and display this message if the internal board temperature becomes excessive.


 


Too low power setting: The DNA 20D puts out a minimum of 4 volts. With low power settings (7 to 8 watts) and low resistance atomizers (below 2 ohms) the DNA will sometimes be unable to provide a low enough power output to be power regulating. If this is the case, the Ohms display will be flashing. The device will still operate.


 


Auto power down
The screen will be at full brightness while firing. After 15 seconds with no button presses, the screen will dim. 4 minutes after the last button press, the screen will fade out and the device will go to sleep mode. Pressing any button will turn the device and display back on.

DNA20 Specs:                             Minimum                                  Max
Output Power                            7 Watts                                     20 Watts
Output Voltage                          4 Volts                                      8.3 Volts
Output Current                                                                           6 Amps
Atomizer Resistance                1.0 Ohms                                  3.3 Ohms
Input Voltage                             3.2 Volts                                   4.3 Volts
Input Current                             1.5 Amps                                  7 Amps

HANA MODS PACK V2 DIMENSIONS:


LENGTH: 1.94"


WIDTH: 1"


HEIGTH: 3.43"


 


WARRANTY WILL BE VOID IF YOU EXCEED THE OPERATING DISCHARGE TEMPERATURE. BATTERY MUST BE INSTALLED PROPERLY.
USE AT YOUR OWN RISK.

Hana Modz - Pack v2

Variable Watt battery pack that lets you control wattage not voltage, for better consistency and repeatability

$250.00
Out Of Stock.*

Latest Reviews

There are no reviews for this product. You could be the first to review!

Write Your Own Review

Hana Modz - Pack v2

Hana Modz - Pack v2

Upload Your Product Photo

I own the rights to this image and confirm that it meets {My Store Name} standards. I have read and accept the Terms and Conditions.

Close

Shop with Confidence

Shopping on 310Vapers is safe and secure, guaranteed.

All information is encrypted and transmitted without risk using a Secure Sockets Layer (SSL) protocol.